Smart greenhouse sensors: which ones do you need?
A smart greenhouse typically measures air temperature and humidity, soil moisture, CO₂, light and irrigation flow. The data reaches a platform, which triggers actions such as ventilation and irrigation.
Request a demoRenokta Ekibi ·

- 1. Sensors measureAir, soil moisture, CO₂, light and flow are measured.
- 2. Gateway collectsData is gathered inside the greenhouse and sent to the platform.
- 3. Platform decidesValues are compared with thresholds and rules.
- 4. Action is triggeredA command goes to the ventilation or irrigation output.
- 5. Result is monitoredNew readings show the effect of the action.
A smart greenhouse typically measures air temperature and humidity, soil moisture, CO₂, light and irrigation flow. The data reaches a platform through a gateway and is used to decide when to run actions such as ventilation and irrigation.
What does an air temperature and humidity sensor do?
Air temperature and humidity describe the environment the plant lives in. Temperature affects growth, while humidity affects disease risk; fungal problems can increase at high humidity. Read together, the two values also show a tendency toward condensation.
The sensor goes at a representative height, away from direct sunlight and ventilation openings. In a large greenhouse a single point is not enough, and measurements are needed in different zones.
Temperature can vary from zone to zone inside a greenhouse. A corner near the door may not give the same values as the middle. The number of sensors is therefore set by the size of the greenhouse and the layout of the plants.
Why is soil moisture measured separately?
Soil moisture shows how much water is actually present at the roots. Air readings do not show this; the soil can be moist even when the greenhouse air is dry. That is why soil moisture is the real basis for irrigation decisions.
The sensor is placed in the root zone and calibrated for the soil type. Different rows in the same greenhouse may hold different amounts of moisture, so several points should be monitored.
The growing medium may be a substrate such as perlite or peat rather than soil. Measurement still takes place in the root zone, but the sensor must suit that medium. Which sensor works in which medium should be confirmed in the manufacturer datasheet.
When are CO₂ and light sensors needed?
CO₂ and light measurements reveal the conditions that affect photosynthesis and yield. In a closed greenhouse the CO₂ level changes during the day, while light varies with the season and weather.
- CO₂ sensor: used to understand the need for ventilation and possible enrichment.
- Light sensor: supports decisions on shading and supplementary lighting.
Not every greenhouse needs both sensors. The need depends on the crop and the operating goals.
Light data can also help plan irrigation timing by showing how conditions change through the day. CO₂ data shows how the level behaves with vents open and closed, which raises the question of whether ventilation is really enough for the plant.
Why is irrigation flow monitored?
Irrigation flow shows how much water was actually delivered to the system. Even if a valve received an open command, a blocked line or a broken pipe may stop water from reaching the target. Flow measurement catches this mismatch.
When a flow meter is read together with soil moisture, you can also see whether the water supplied shows up in the soil.
Which actions does sensor data trigger?
The platform compares sensor values with rules and sends commands to outputs such as relays or valves. The two most common actions are ventilation and irrigation.
- Ventilation: when a temperature or humidity threshold is exceeded, vents open and fans run.
- Irrigation: when soil moisture falls below the lower limit the valve opens, and it closes once the target is reached.
- Alert: if a value changes unexpectedly, a notification goes to the person in charge.
What is the difference between a prototype and an industrial system?
A prototype is usually built from low-cost development boards and ready-made sensors for learning and trying things out. An industrial system needs enclosures that withstand humidity, dust and heat, reliable communication, remote management and a maintenance routine.
In a commercial greenhouse the cost of downtime is high, so redundancy, alarms and record keeping matter more. The level required depends on the size of the greenhouse and the value of the crop.
Another difference is maintenance and calibration. Sensors can drift over time and degrade in humid conditions, so a periodic check plan should be considered from the start. A prototype that works well does not mean the same solution will run without interruption through a whole season.
Conclusion
A smart greenhouse starts with the right measurements: when air, soil, CO₂, light and flow are read together, ventilation and irrigation decisions rest on data. For a suitable sensor set and setup for your greenhouse, see our smart agriculture and greenhouse solution page or contact us for a needs discovery.
Frequently asked questions
- What are the minimum sensors for a smart greenhouse?
- Air temperature and humidity plus soil moisture are often seen as the basic set to start with. CO₂, light and irrigation flow are added depending on the crop and the goal.
- Does a soil moisture sensor need calibration?
- Yes. Soil type affects the reading, so the sensor should be calibrated in the soil that will be used and its values checked periodically.
- Is a CO₂ sensor required in every greenhouse?
- No. It is useful in closed and intensive production, and the need depends on the crop and the operating goals.
- Can irrigation be automated?
- Yes. The platform compares values such as soil moisture with rules and opens and closes the valve. It is advisable to verify the rules by monitoring them manually at first.
- Is a prototype system enough for a commercial greenhouse?
- Usually not. A prototype is for learning and testing, while a commercial greenhouse needs durable enclosures, reliable communication, alarms and a maintenance routine.
