Skip to content
RenoktaRenokta

What Is OEE? How to Calculate and Improve It

OEE shows how effectively a machine runs during planned production time. It is calculated by multiplying availability, performance and quality.

Request a demo

Renokta Ekibi ·

A live process chart on the touch panel beside an injection moulding machine.
OEE calculation flow
PlannedtimeAvailabilityPerformanceQualityOEE
  1. 1. Planned timeThe total time set aside for production is defined.
  2. 2. AvailabilityStops are subtracted to find actual run time.
  3. 3. PerformanceActual speed is compared with ideal speed.
  4. 4. QualityThe share of parts right the first time is calculated.
  5. 5. OEEThe three ratios are multiplied for overall effectiveness.

OEE (Overall Equipment Effectiveness) shows how effectively a machine or line runs during its planned production time. It is found by multiplying availability, performance and quality. A score of one hundred percent would mean no stops, full speed and no defects.

What are the three components of OEE?

OEE measures loss from three separate angles, and each is expressed as a ratio.

  • Availability: how much of the planned time did the machine actually run? Breakdowns, setups and waiting lower it.
  • Performance: while running, how close was it to ideal speed? Slow running and short stops lower it.
  • Quality: how many parts came out right the first time? Scrap and rework lower it.

How is OEE calculated?

The formula is simple: OEE = availability × performance × quality. All three ratios are written between 0 and 1, or as percentages, and multiplied together.

Here is a fictional example. Suppose a machine runs for 90 percent of planned time, reaches 80 percent of ideal speed while running, and 95 percent of its parts are defect-free. Then OEE = 0.90 × 0.80 × 0.95 = 0.684, or about 68 percent. These numbers are invented only to show the arithmetic and are not a real measurement.

Why track the three ratios separately?

A single OEE percentage does not say where the loss is. Two machines with the same score can have completely different problems: one may stop often, the other may run slowly.

That is why the components are tracked on their own. The lowest ratio shows where to start improving. Looking for the loss in the wrong place wastes both effort and time.

What data does OEE need?

OEE needs at least three pieces of data: whether the machine is running, the total parts produced and the number of defective parts. Planned time and the ideal cycle time per part are added to these.

  • Run status: can be captured automatically from a sensor, a PLC signal or a current measurement.
  • Part count: read from a counter or the PLC.
  • Stop reason: recorded with a code the operator selects.
  • Defective parts: taken from the quality control record.

Data entered by hand arrives late and is often incomplete. Automatic collection is the first condition for a trustworthy OEE.

Which losses reduce OEE?

OEE losses are usually grouped into six headings: breakdowns, setup and changeover time, small stops, reduced speed, startup rejects and production rejects. The first two affect availability, the next two affect performance, and the last two affect quality.

Sorting losses under these headings shows which component each stop lowers. Meetings then run on data instead of opinion.

Short stops, for instance, often never reach the stop log but quietly lower performance. Automatic counting exposes this hidden loss and becomes one of the first improvement opportunities.

How can OEE be improved?

The way to improve OEE is to find the biggest loss first and then focus on it. Each of the three components has its own typical remedies.

  • For availability: classify stop reasons, shorten setup times and organize planned maintenance.
  • For performance: examine causes of slowdowns and short stops, and verify the ideal cycle time.
  • For quality: find the source of defects and monitor first-piece approval and process parameters.

What should you watch for when reading OEE?

OEE is a diagnostic tool, not a target score. Comparing different machines or plants with a single percentage can mislead, because ideal speed and planned time may be defined differently.

To keep the calculation consistent, define the ideal cycle time, the planned time and which events count as stops in writing from the start. If definitions change, comparison with past data breaks down.

Conclusion

OEE splits production loss into three parts so you can see where to focus. For it to work, data on stops, part counts and defects must be collected automatically. To discuss how you could collect it on your floor, see our smart factory and MES solution page or contact us for a needs discovery session.

Frequently asked questions

What is the OEE formula?
OEE = availability × performance × quality. The three ratios are multiplied as percentages, and the result shows how effectively a machine ran during planned time.
What is a good OEE value?
There is no universal target. The value varies with the industry, product and definitions. The most useful comparison is against your own past data using the same definitions.
Why is calculating OEE by hand not enough?
Hand-entered data is late and incomplete. When stops and part counts are collected automatically, OEE becomes more reliable and can be followed in real time.
Which machines is OEE used for?
It is most meaningful for machines and lines that make repeated products. It can be calculated per line or per single machine.
How are OEE and MES related?
An MES collects stop, production count and defect data from the floor and calculates OEE automatically. OEE is one of the outputs an MES provides.

Let's plan the right solution for you, together.

Request a demo